安博（中国）股份有限公司官网

Key: Blow Molding Machine,Plastic Bottle Blowing Machine,Plastic Blowing Machine,Blow Moulding Machine

Blow Molding Machine Total：1 products

Blow Molding Machine CPX
YSXZB Series automatic rotary preformed cup filling and sealing machine is applicable to pack the products like yogurt ,milk,mineral water, beverage , ice cream, seasoning and so on.The process is from cup separating, sup falling,quantitive filling, suck cap film,sealing,and product conveying.The choice of the machine model and number of filling heads depends on the factors like required output, size and type of packaging and requirements for additional equipment. The machine can provide a lot of solutions for the below field:suitable for both traditional and innovative packaging designs, quick change-over to alternative packaging, different ways of container closing. Applicable Filling material:Liquid:yogurt ,milk,mineral water, beverage , ice cream, seasoning and so on Cap film material:Al+plastic laminated film;paper+plastic laminated film. Pre-cut lid or film roll. Preformed cup type: Paper cup,Plastic cup,Alu.cup etc.
Main Technical Data:
Function name	Brand	Brand country	Function name	Brand	Brand country
Main motor	SEW	German	Operation center	SIEM ENS	German
High pressure combination valve	Eugen Seitz	Switzerland	Low voltage electrical appliance	Schneider / SIEM ENS	France /German
Stretch cylinder	Rexroth	German	Infrared heating tube	PHILIPS	Netherlands
Linear Guides	Rexroth	German	Infrared thermometer	OPTEX	Japan
Gas source filter	FESTO	German	Encoder	SICK	German
Torque clutch	MAYR	German	Limit switch	OMRON	Japan
Low pressure control solenoid valve	MAC	USA	Photoelectric switch	SICK	German
Frequency converter	Schneider	France	Proximity switch	SICK	German
PLC	SIEMENS	German	Intermediate relay	OMRON	Japan
Program mable Controllers	SIEMENS	German

Main parameter:

PRODUCTION DATA		Mould cavities	N	16
		Max. body diameter	mm	75
		Max. Height	mm	260
		M. diameter	mm	38
		Max. preform Height	mm	140
		Max. capacity	ml	750
		Nominal output for 500ml, bottle(*)	pcs/h	32000
DIMENSIO NS	Host	Length Width) Height	mm	3800X2400X3200
	Host	Weight	kg	21000
	Heating furnace	Length) Width) Height	mm	5800X1400X2200
	Heating furnace	Weight	kg	2500
ELECTRICAL FEEDING		Voltage	V	380
		Frequency	Hz	50
		Total power installed	kW	260
		Main motor power installed	kW <	5.5 <
		Medium power absorbed(**)	kW	80-100
COOLING /HEATING SYSTEM	BASE MOULD	Water inlet	℃	10~20
		Water inlet pressure	bar	5
		Flow	m3/h	10
	BODY MOULD	Water inlet temperature(**)	℃	10~20
		water inlet pressure	bar	5
		Flow	m3/h	18
	Heating furnace But water	Cooling water temperature(**)	pressure	10~20
		Water inlet pressure	bar	5
		Flow	m3/h	8
SERVICE AIR		Nominal pressure	bar	High pressure to low pressure
		Air rate (**)	m3/min
		Filtering grade (filter)	micron
		Humidity
BLOW AIR		Nominal pressure	bar	40
		Air rate (**)	m3/min	20
		Filtering grade(filter)	micron	0.01μ
		Maximum pressure dew point	℃	+3℃
		Oil		Maximum concentration 0.01 mg/ m3
HEATING		Heating groups * pcs	n	16*6
ENVIRONMENT		Environment temperature (**)	℃	(20℃-35℃)±3℃
		Environment humidity ( without condensate)	%	≤70%
		Max. altitude (over sea)	m
CONNECTIONS		Connection service air	Inch.	1
		Connection blow air	Inch.	2
		Connection water and oil	Inch.	2

Main technique:

1) Hopper and feeding mechanism: computer monitoring, no need for assistance; according to different types of preforms, the output speed can be adjusted arbitrarily
2) Heating furnace: When heating, the preform rotates while moving forward in the furnace to make the wall of the preform heat evenly; specially designed rapid hair cooling device; specially designed defective preform detection and ejection device
3) Blowing part: full monitoring by the host computer during the entire blowing production process
4) Special formwork system: The mold base is equipped with a pressure balance device to minimize the mold clamping line of the bottle during the molding of the bottle, ensuring the quality and performance of the bottle.
5) Stretching secondary blowing system: secondary blowing system, pre-blowing, high-pressure forming blowing, secondary blowing pressure, time adjustable .
6) Manipulator device: Made of stainless steel, precision machining; rotary manipulator with torsion overload protection to prevent equipment damage when equipment is not damaged
7) Safe and reliable mechanical transmission: using variable frequency motor, gearbox and inverter of SEW Company of Germanyod grade requirements.
8) Mold: audited by professional designers
Description:	1. Actual production depends on preform shape, preform wall thickness, bottle design and section quality
	2. Change according to different generation conditions, pressure and other factors
	3. The above water, electricity and gas parameters are calculated on the basis of 500ml water bottle.